INOX FLAG REMOTE CONTROLLED. With 360 degree rotary unit and remote control.

304 stainless steel flagpole with wireless control system. Maybe from 200 meters away. Customize the flag automatically up or down the flag completely automatically for stainless steel flagpole . With 360 degree rotary unit and remote control for sus 304 stainless steel flagpole . There is a fully automatic wiring system with wireless remote control. Electricity use is absolutely safe. Automatically shut off electricity completely when leaking. DC power for flagpoles. High level with TINTA stainless steel flagpole .

RECOMMENDED USE: For engine used for TINTA stainless steel flagpole.

Specialized engine used for this stainless steel flagpole, suitable for diameter of stainless steel flagpole body (engine mount) is from 20cm (cylinder 200) or more. Because of the large engine block size. The stainless steel flagpoles with the diameter immediately installed in the engine but the body diameter is lower or less than 200mm (20 cm), it can not be installed and used normally.

If you want to buy this stainless steel flagpole engine set. Carefully measure the diameter of your flagpole at the engine mounting location before you buy! Or call 0987636779 for advice.

To ensure the stainless steel flagpole with specialized engine runs the best. Please contact a professional who is TINTA VN Inox Joint Stock Company. There are specialized engineers. Having many years of experience. Specialized machinery for manufacturing and processing 304 stainless steel flagpole . TINTA will advise and ensure you the synchronization and the best of stainless steel flagpoles rotating 360 degrees. Fully automatic.

However, if you still want to buy a 360-degree rotary controller with fully automatic flag raising and control system, you can press the button on the remote control. TINTA always welcomes you.

Instructions to ensure the use of 304 stainless steel flagpole motor properly.

Welcome to TINTA stainless steel flagpole products. Please do not hesitate. Please call TINTA customer service. Hot line: 0987636779 - 028 66736186.

List of standard configuration for processing 304 stainless steel flagpole using electric motor. Remote control. Fully automatic. Raise the flag. Lowering the flag.. . Just press the remote control button. Distance up to 200 meters.

1. Electric flag pole controller

2, electric flagpole motor.

3, manual shaker.

4, lifting the remote control 2.

5, guide one.

Guide new smart stainless steel flagpole control system.

Firstly. Product introduction.

The control system consists of two parts: 304 stainless steel flagpole engine and controller. This system is the latest product of Inox TINTA. Using some smart sensor technologies and adding many new functions compared to traditional stainless steel flagpole engines:

1. With 24V low voltage control. There is absolutely no risk of leakage in an environment where the flagpole stems are slightly wet and damp.

2. The use of the position sensor is accurate. Exactly as if the flag was raised manually. Or the flag is lowered in any position. Normally the remote control unit will operate immediately when the button is pressed. Absolutely will not tangle the flag zipper, or stop incorrectly the desired position.

Automatic motor system, safety functions for users.

3. With overload protection function. In extreme conditions such as stormy weather, tornadoes. If there is a phenomenon of tangled wires, mechanical parts getting stuck, etc. The automatic overload protection function of the flag puller will stop the engine. The protection function will automatically stop the engine to protect the safety system.

4. Replace the new switch system with traditional flag pull function with a high-sensitivity sensor. Easy to install and easier to use. Basically doing the operation is really very simple.

5. Zoom out. The minimum size of the control system type can be used in flagpoles of 160mm diameter. With the height of 304 stainless steel flagpole can reach about 15 meters.

6. The new clutch allows manual use. When there is no power supply, use a gearbox. Return the gear to manual mode. The manual operation becomes easier.

7. Using motors not contaminated with electricity. Use large torque.

Second, the product parameters automatic flagpole controller.

Use voltage: AC220V input, DC24V output.

Capacity: adjust according to the height of the flagpole 20-100W.

Flag height: Within 30 meters.

Speed: Type A: 0.36 m / sec.

Speed ​​of Type B: Adjust the speed of the raised flag according to the length of the national anthem.

Remote control distance: More than 200 meters (antennas pulled out by metal tubes, open space).

Lifting force according to torque: more than 10 kg.

Operating environment: temperature - 30 ° C - 70 ° C, humidity below 85%.

Table describing the function of the remote control panel and control panel (as shown).

For more details about processing 304 stainless steel flagpole. Please call 0987636779 - 028 66736186.